New Products from ASIHome!

Intermatic 178PA28A - Air Temperature Sensor for PE653

ASIHome — Mon, 28 Jun 2010 00:00:00 -0400

Description: Air Temperature Sensor for PE653.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Intermatic PE653RC - MultiWave Z-Wave Pool/Spa Controller w/Remote

ASIHome — Mon, 28 Jun 2010 00:00:00 -0400

Description: Prepare to automate your Pool/Spa and even your Home with the most technologically advanced wireless control system in the market today! The MultiWave is designed as a "plug and play" system! Install the water sensor and watch the MultiWave thermostat come alive to maintain your pool and/or spa water temperatures. Install the air sensor and watch the MultiWave freeze protection system come alive to protect your investment. Connect your equipment to the intelligent RS485 communication port and watch the MultiWave recognize and control your equipment with ease.

Features:

Internal 24-Hour Digital Clock
Memory Back-Up
Wireless Handheld Controller
Backlit LCD Readout
Water Proof Hand Held
Full Variable Speed Control
Control Five Pool/Spa Functions
Three ON/OFF Events Per Equipment
120VAC or 208/240VAC Input And Control
Programmable Heater Cool
Relay 1 - 17A Resistive, 17FLA/80LRA @ 120/240VAC 50/60Hz
Relay 2 - 15A Resistive, 10FLA/60LRA @ 120/240VAC 50/60Hz
Control Supply - 120/240VAC, 50/60Hz 5 Watts Maximum

Notice/Warning: For Freeze detection or Air temperature, use the 178PA28A. Use with a controller such as HomeSeer or the MiCasaVerde Vera. Support is pending from both of these devices.

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AT004 - A-10/X-10 Master Test Trasmitter and Programmer

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Description: The AT001 is both an A10 enhanced or standard X-10 based test transmitter. Selection of A10 (6V peak to peak) transmission or X-10 (3V peak to peak) signal output is accomplished with a switch inside the sliding cover on the AT001.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AT001 - A-10/X-10 Test Transmitter

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AF310 - 277VAC, 2-Wire Low/Band-Pass X-10 Filter

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Description: The AF310 is a Line Noise Attenuator which is parallel tuned and, therefore, attenuates noise and unwanted signals of frequencies above or below 120 kHz without attenuating the PCC signal. It attenuates spikes and transients having rise times which are too fast to be affected by conventional spike suppressors.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AF300 - 277VAC, 3-Wire Low-Pass Blocking X-10 Filter

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Description: The AF300 is a Line Isolation Filter which filters out PCC command signals and any strong electric clutter at 120 kHz on the AC line. It provides attenuation at a 40:1 ratio input to output respectively. It prevents passage of the PCC command signals or 120 kHz electronic noise from the line side (primary) to the load side (secondary) and vice versa. The AF300 is for applications up to 277 volts.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AF100 - 5A 120VAC Plug-In X-10 Filter

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Description: Prevent "noisy" appliances from interfering with X-10 signal. Also can be used to isolate uninteruptible power supplies and line conditioners from "sucking" the X-10 signal off the line.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACT AC100 - 5A HID Choke for X-10 Systems

ASIHome — Thu, 24 Jun 2010 00:00:00 -0400

Description: 5A HID choke for X-10 systems.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

ACNC DP28BN - DoorBell Fon System with Brass Door Intercom Station For Nutone IR6 or IA70 Boxes

ASIHome — Thu, 19 May 2005 00:00:00 -0400

Add safety and security to your home with an easy to install intercom at your front door! Now you can talk to the person at your front door without opening the door, using any telephone in the house!

The Doorbell Fon is the best high quality, inexpensive modular telephone entry system on the market. The Doorbell Fon allows users to answer a door or gate from any telephone in their home. This door phone installs using a single pair of wire for basic kit as well as modular add-ons.

All communication is carried over a single pair of wires. Operation is simple. NO PROGRAMMING! NO CODES! Just pick up the phone like a regular phone call.

Features:
Installs using single pair of wire. Use existing door bell wire.
Can operate two different entries with same system.
Distinctive ring for each entry.
Built in call-waiting.
Works with single, two-line, PBX and Key systems.
Works with cordless phones and answering machines.
Modular design for future components.
Convenient surface mount design.
Weather resistant.
2-year warranty.
When a visitor presses the call button on the door box, the telephones will ring with a distinctive ring. Pick up the telephone and you are connected to the door automatically. If you are on the telephone you will hear a call waiting tone. Simply hit the "flash" key or hook switch on your phone. The Doorbell Fon will place your call on hold and connect you to the door or gate.

Power: 117VAC/60Hz 0.1 Amp 12 Watt Output: 17-28 Volt (talking);75-vrms/25 +/- 2Hz (ringing) Operating Temperature: -20°F to 120°F

Doorbell Fon Kit includes controller and door station

NOTE:This system is designed to work with Nutone IR6 or IA70 mounting brackets, and has an brass faceplate.

Acme 652132R - 7/8" Monel Staple for the Acme 75A

ASIHome — Fri, 18 Jun 2010 00:00:00 -0400

Description: 5/8" Resin Coated Staple for use with the Acme 75A tacker/stapler. Not for use with the 75AC. 1000 staples per box.

Notice/Warning: Monel is similar to Stainless Steel

Specifications
Brochure
Installation Manual
Owner's Manual

Add-A-Motor D20 - Chicken Coop Door Motor

ASIHome — Fri, 18 Jun 2010 00:00:00 -0400

Description: You decide what time your chicken coop door opens and closes - thereafter its automatic! Sleep a little later. The D20 opens the door each morning allowing your hens to feed or free-range on their own. If you arrive home late, or if the weather is so poor you cant attend your coop on-time, relax because chickens enter the coop about the same time every day, and the D20 will automatically close the door at the time you set. You can also set multiple door openings and closings each day. This can benefit in several ways. It can influence egg production by exposing hens to longer periods of daylight by preventing them from re-entering the coop too soon. It can foil small predators that sneak-in to steal eggs after your hens are out. And, it can help manage heat inside the coop. Raccoons, fox, dogs, cats, coyotes, etc. eventually give up and go elsewhere.

Features:

Includes motor, mounting bracket, AC-DC Adapter, lift cable and illustrated instructions
Has a reversible motor with open and closed stop settings
Motor stops door at positions you set
Motor can lift-lower a door up to 4 pounds, with a door opening up to 25 inches
Motor lifts and lowers door smoothly in a few seconds, no sudden drops
If your door swings open, convert it to vertical lift by installing it in side-channels
Plug-in ready to your lamp timer switch, X-10 control, battery, or our "Butler" remote control

Notice/Warning: Do not use M80 for Chicken Coop Door applications.

Specifications
Brochure
Installation Manual
Owner's Manual

Leviton 41084-BTB - Quickport Snap-In Blank Insert-Light Almond

ASIHome — Tue, 15 Jun 2010 00:00:00 -0400

For use with Leviton Quickport plates, these handy snap-in blanks allow you to create your own custom multimedia plates. add the appropriate jacks to the Quickport plate, then snap these blanks in to cover any unused ports. That's all there is to it! Available in White, Almond, and Ivory.

Must be ordered in multiples of 10.

Leviton 41084-BGB - Quickport Snap-In Blank Insert-Grey

ASIHome — Tue, 15 Jun 2010 00:00:00 -0400

Must be ordered in multiples of 10.

Leviton 41084-BEB - Quickport Snap-In Blank Insert-Black

ASIHome — Tue, 15 Jun 2010 00:00:00 -0400

Must be ordered in multiples of 10.

Leviton 41084-BBB - Quickport Snap-In Blank Insert-Brown

ASIHome — Thu, 08 Apr 2004 00:00:00 -0400

Must be ordered in multiples of 10.

Arlington Industries TL50P - The LOOP - 5" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning: "UV" rated.

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries TL50 - The LOOP - 5" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries TL25P - The LOOP - 2-1/2" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning: "UV" rated.

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries TL25 - The LOOP - 2-1/2" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries TL20P - The LOOP - 2" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning: "UV" rated.

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries TL20 - The LOOP - 2" Cable Support

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Hanger for communications cable support. For CAT 5, 6, 7 cable and fiber optic cable.

Features:

Easy to use...cheaper than trays!
Flexible and non-metallic
Holds 2" to 5" diameter bundle of CAT 5 or fiber optic cable - without damaging the cable
Versatile mounting - rotates to any angle!
TL25 holds the same amount of cable as a J-hook, at half the cost!

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T23T - Cable Way Wire Tray Tee

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T23H - Cable Way Wire Tray Support Bracket

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T23E - Cable Way Wire Tray End Cap

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T23C - Cable Way Wire Tray Coupling

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T23A - Cable Way Wire Tray Angle

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries T205 - Cable Way Wire Tray - 5'

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Cable support system for either power or low voltage cable. For new construction or retrofit. Non-metallic.

Features:

Secure, UL Listed as a cable support system
For power or low voltage cable
Support brackets attach directly to framing members, without structural damage
Time saving system - no holes to drill through joists
Brackets hold cables in place - open the bracket for easier cable insertion
Slide-on trough protects and covers cable
Install additional trough sections as needed and join them together with couplings
Push-on end caps complete the job

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries SP100 - Safety Plate

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Protects wiring from nails, screws, etc.

Features:

Flat 16-gauge steel

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries SC5 - CAM-KIT Security Camera Mounting Kit

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Security camera mounting kit. Universal bracket mounts to 3-1/2" and 4" round or octagon boxes and single-gang device boxes. Also fits, FL430 CAM-LIGHT box.

Features:

Fits any hole pattern
Low cost
Installs in less than two minutes
Installs cameras with a base diameter upto 4-1/2"

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Arlington Industries SB130 - Non-Metallic Bushing for Metal Studs

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: These bushings fit existing irregular shaped holes in metal studs, alleviating the need to punch holes in metal studs, weakening the structural member. Use these bushings to comply with paragraph 300-4(b)(1) of the 2005 NEC code which states that: "In both exposed and concealed locations where nonmetallic-sheathed cables pass through either factory or field punched, cut, or drilled slots or holes in metal members, the cable shall be protected by bushings or grommets covering all metal edges and securely fastened in the opening prior to installation of the cable."

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

rlington Industries RW3 - Reducing Washer 1" to 3/4

ASIHome — Mon, 14 Jun 2010 00:00:00 -0400

Description: Plated steel reducing washer.

Notice/Warning:

Specifications
Brochure
Installation Manual
Owner's Manual

Malibu 8100-9120-01 - 120W Transformer, Timer and Photocell Power Pack

ASIHome — Thu, 03 Jun 2010 00:00:00 -0400

Description: 120W Transformer and Timer Power Pack. Includes Photo Eye for day/night. Does not use trippers but has digital timer settings.

Notice/Warning: Not for use with submersible lights/pumps. 18 gauge minimum wiring.

Specifications
Brochure
Installation Manual
Owner's Manual

ButtKicker BKA3A130C - Mini Power Amplifier for MINIBKLFE

ASIHome — Thu, 03 Jun 2010 00:00:00 -0400

Description: Designed to power one mini-Concert or two mini-LFE's.

Features:

100W @ 2 ohms
100W @ 4 ohms

Notice/Warning: Required to power the BKMINICT or BKMINILFE.

Specifications Brochure Installation Manual Owner's Manual

ReadySolar 666-0000-00 - Solar-in-a-Box Expansion Box

ASIHome — Wed, 02 Jun 2010 00:00:00 -0400

Description: Solar in a Box is the worlds first completely pre-assembled, all AC solar electric system. High quality and leading edge components are assembled in a factory controlled environment. This significantly reduces the complexity of design and installation of a solar electric system.

In addition to reduced installation costs, the unique Solar in a Box design offers end users distinct performance and aesthetic benefits.

Includes:

5' interconnect cable
Junction box with strain reliefs

Notice/Warning: One required per group of 5 rooftop units after the first group of 5. All ReadySolar products are direct shipped from the manufacturer so actual shipping will apply.

Visit http://www.dsireusa.org/ to find applicable rebates in your area.

Specifications
Brochure
Installation Manual
Owner's Manual

ReadySolar 5520-0001 - Solar-in-a-Box Extension Cable Bundle

ASIHome — Wed, 02 Jun 2010 00:00:00 -0400

Description: Extension cable bundle for increasing distance between rooftop units or between rooftop unit and J-Box.

Includes:

6' extension cable (5508-0001) x4
12' extension cable (5509-0001) x2
20' extension cable (5510-0001) x1

Notice/Warning: One required per system. All ReadySolar products are direct shipped from the manufacturer so actual shipping will apply.

Visit http://www.dsireusa.org/ to find applicable rebates in your area.

Specifications
Brochure
Installation Manual
Owner's Manual